A baseball bat is divided into several regions. The "barrel" is the thick part of the bat, where it is meant to hit the ball. The part of the barrel best for hitting the ball, according to construction and swinging style, is often called the "sweet spot". The end of the barrel is called the "top", "end" or "cap" of the bat. Opposite the cap, the barrel narrows until it meets the "handle". The handle is comparatively thin, so that batters can comfortably grip the bat in their hands. Sometimes, especially on metal bats, the handle is wrapped with a rubber or tape "grip". Finally, below the handle is the "knob" of the bat, a wider piece that keeps the bat from slipping from a batter's hands.
How the bat is made is what differentiates it from the typical regulation bat used by major league players. In addition to being lighter and thinner, the bat is also much longer compared to the normal bat. It ranges between 35 – 37 inches in terms of length. In terms of weight, the bat weighs between 17 – 22 ounces. Of great importance to note is the fact that the bat features a bigger barrel than the normal ones. Since it’s flatter and features a small diameter, it’s ideal when it comes to hitting ground balls as well as pop flies. This would be necessary during the fielding practice of any team regardless of the level.
Baseball bats are made of either wood, or a metal alloy (typically aluminum). Most wooden bats are made from ash. Other woods include maple, hickory, and bamboo. Hickory has fallen into disfavor over its greater weight, which slows down bat speed, while maple bats gained popularity following the introduction of the first major league sanctioned model in 1997. The first player to use one was Joe Carter of the Toronto Blue Jays. Barry Bonds used maple bats the seasons he broke baseball's single-season home run record in 2001, and the career home run record in 2007. In 2010, the increased tendency of maple bats to shatter has caused Major League Baseball to examine their use, banning some models in minor league play.
At bat Baltimore chop Bat flip Chinese home run Batting count Bunt sacrifice bunt slap bunt squeeze play Checked swing Cleanup hitter Designated hitter Double Double switch Foul ball Foul tip Golden sombrero Grand slam Ground rule double Hat trick Hit Hit and run Hit by pitch Hitting for the cycle Home run Infield hit Inside-the-park home run Leadoff hitter Lefty-righty switch Line drive Moonshot Plate appearance Platoon system Pull hitter Sacrifice fly Single Strikeout Strike zone Sweet spot Switch hitter Triple Walk Walk-off home run
Within league standards there is ample latitude for individual variation, many batters settling on their own bat profile, or one used by a successful batter. Formerly, bats were hand-turned from a template with precise calibration points; today they are machine-turned to a fixed metal template. Historically significant templates may be kept in a bat manufacturers' vault; for example, Babe Ruth's template, which became popular among major-league players, is R43 in the Louisville Slugger archives.
The most obvious reasons to utilize a fungo bat is the fact that it’s lightweight. It’s handy to coaches when conducting fielding practice since he or she has to hit plenty of balls to warm up his or her players. What is for sure is that hitting countless balls during practice can be tiring. Consequently, having a bat that’s lighter weight is magical at preventing the coach and/or players from getting tired.
If your high school or travel team has at least two coaches, you can use what Bates calls a two-fungo drill. One coach can hit to third and second, while the other hits to short and first. If catchers are finished working with the pitchers, they can feed balls to the fungo hitters. The idea is for the third baseman to practice turning a 5-4-3, with the first baseman moving up toward second base about 60 feet instead of 90, with a net behind him to catch overthrows. The shortstop works on throwing across on 6-3s.
The main goal of the game is to hit it to the pin in the least amount of strokes, similar to golf. Holes can consist of a certain sign in the outfield, in the tarp tunnel, off of the foul pole, onto the pitchers mound or off of a yardage marker on the outfield wall; it can really be anything on the field that can be hit without breaking. There can even be 2 part holes such as: First you have to hit the ball off of the scoreboard, then you have to hit the ball off of the right field foul pole.