The bat's form has become more refined over time. In the mid-19th century, baseball batters were known to shape or whittle their own bats by hand. This allowed there to be a wide variety in shape, size, and weight. For example, there were flat bats, round bats, short bats, and fat bats. Earlier bats were known to be much heavier and larger than today's regulated ones. During the 19th century, many shapes were experimented with, as well as handle designs. Today, bats are much more uniform in design.
Many players "bone" their bats, meaning that before games, they rub their bats repeatedly with a hard object, believing this closes the pores on the wood and hardens the bat. Animal bones are a popular boning material, but rolling pins, soda bottles and the edge of a porcelain sink have also been used. Pete Rose had his own way of hardening his bats: he soaked them in a tub of motor oil in his basement then hung them up to dry.
A baseball bat is divided into several regions. The "barrel" is the thick part of the bat, where it is meant to hit the ball. The part of the barrel best for hitting the ball, according to construction and swinging style, is often called the "sweet spot". The end of the barrel is called the "top", "end" or "cap" of the bat. Opposite the cap, the barrel narrows until it meets the "handle". The handle is comparatively thin, so that batters can comfortably grip the bat in their hands. Sometimes, especially on metal bats, the handle is wrapped with a rubber or tape "grip". Finally, below the handle is the "knob" of the bat, a wider piece that keeps the bat from slipping from a batter's hands.
There are many advantages to using a fungo bat. If you are a coach or a parent looking to improve your player's defensive skill set, you're going to want and need a fungo bat. A normal adult wooden baseball bat will weigh around 27-31 ounces, and after a couple of rounds of pop-flys, it is going to feel like you just went through a full-on workout. With the help of a fungo bat, you will be able to hit ground balls and pop flys all day without getting fatigued. The barrel on a fungo bat will typically be 2 1/4 inches in diameter which greatly helps increase your control over the bat through the hitting zone. While the barrel has a much more thin diameter, it is also much longer in comparison to a normal wood baseball bat. This larger hitting surface and smaller barrel combine to give coaches and parents quick swing speeds with precise accuracy.
“They’re not moving, their feet are apart, their gloves are on the ground, backs are flat, and they’re working down to up, out to in, basically a steady roll back and forth probably 15 to 20 each,” Bates said. “Then they’ll turn their body, work glove side for another 15 to 20, and backhand 15 to 20. No movement, really, just making sure we’re watching the ball roll into our glove, fielding it, and doing all the things fundamentally correct.”
Chris Coste, a former catcher for the Philadelphia Phillies who coaches at Division III Concordia, in Moorhead, Minn., agreed. “When baseball is every single day, you’ve got to do things differently,” he said. “In the big leagues, they get so many ground balls during batting practice that infield is more for the fans and more for the scouts and things like that. At this level, we need it, and we love doing it.”
The Wright & Ditsons Lajoie baseball bat. This bat had a normal size barrel but had two knobs on the handle. The lowest knob was at the bottom of the handle and the other knob was roughly two inches above the lowest knob. This was designed to have better spacing between the hands due to the knob being in the middle of the grip. This also gave batters an advantage when they choked up on the bat, because the second knob provided a better grip.
Maple bats in particular were once known (circa 2008) to potentially shatter in a way that resulted in many sharp edges, sometimes creating more dangerous projectiles when a bat broke. Maple bat manufacture evolved significantly, in cooperation with Major League Baseball, paying special attention to grain slope, and including an ink spot test to confirm safest wood grain orientation.
The most obvious reasons to utilize a fungo bat is the fact that it’s lightweight. It’s handy to coaches when conducting fielding practice since he or she has to hit plenty of balls to warm up his or her players. What is for sure is that hitting countless balls during practice can be tiring. Consequently, having a bat that’s lighter weight is magical at preventing the coach and/or players from getting tired.
Once the basic bat has been turned, it has the manufacturer's name, the serial number, and often the signature of the player endorsing it branded into it opposite the wood's best side. Honus Wagner was the first player to endorse and sign a bat. Next, most bats are given a rounded head, but some 30% of players prefer a "cup-balanced" head, in which a cup-shaped recess is made in the head; this lightens the bat and moves its center of gravity toward the handle. Finally, the bat is stained in one of several standard colors, including natural, red, black, and two-tone blue and white.
Baseball bats are made of either wood, or a metal alloy (typically aluminum). Most wooden bats are made from ash. Other woods include maple, hickory, and bamboo. Hickory has fallen into disfavor over its greater weight, which slows down bat speed, while maple bats gained popularity following the introduction of the first major league sanctioned model in 1997. The first player to use one was Joe Carter of the Toronto Blue Jays. Barry Bonds used maple bats the seasons he broke baseball's single-season home run record in 2001, and the career home run record in 2007. In 2010, the increased tendency of maple bats to shatter has caused Major League Baseball to examine their use, banning some models in minor league play.
Secondly, the first base fungo hits balls to the third baseman, who turns a double play with the second baseman to the normal first baseman, while the third base fungo hits balls to the shortstop, who throws to a shortened deep firstbaseman (this means that the deep firstbaseman stands closer to the shortstop than normal, so that the throw across this infield is the correct distance - this does NOT mean that the deep man stands any closer to the normal first base position - this length should always be sufficient)