Maple bats in particular were once known (circa 2008) to potentially shatter in a way that resulted in many sharp edges, sometimes creating more dangerous projectiles when a bat broke. Maple bat manufacture evolved significantly, in cooperation with Major League Baseball, paying special attention to grain slope, and including an ink spot test to confirm safest wood grain orientation.
For starters, we should clarify just what we’re talking about when we say fungo bat. Longer, lighter and thinner than a regulation bat (but a larger barrel), a fungo bat is typically 35 to 37 inches long, and weighs between 17 and 22 ounces. As David Allison wrote in the June 1978 edition of Country Journal, “A fungo bat looks to be a cross between a baseball bat and a broomstick.”
How the bat is made is what differentiates it from the typical regulation bat used by major league players. In addition to being lighter and thinner, the bat is also much longer compared to the normal bat. It ranges between 35 – 37 inches in terms of length. In terms of weight, the bat weighs between 17 – 22 ounces. Of great importance to note is the fact that the bat features a bigger barrel than the normal ones. Since it’s flatter and features a small diameter, it’s ideal when it comes to hitting ground balls as well as pop flies. This would be necessary during the fielding practice of any team regardless of the level.
The fungo is used by a coach to hit balls for defense practice. It is lighter weight, so less fatiguing to hit ball after ball. The fungo sheds its weight above the hands. The severely tapered barrel to drops weight and maintains a high moment of inertia. While the bat would be at greater risk of breaking if used in a live batting exercise, it is safe to use in practice because there are much fewer mis-hits.
The Wright & Ditsons Lajoie baseball bat. This bat had a normal size barrel but had two knobs on the handle. The lowest knob was at the bottom of the handle and the other knob was roughly two inches above the lowest knob. This was designed to have better spacing between the hands due to the knob being in the middle of the grip. This also gave batters an advantage when they choked up on the bat, because the second knob provided a better grip.
Manufacturers position each bat's label over the mechanically weaker side of the wood. To reduce chance of fracture, and maybe deliver more energy to the ball, a bat is intended to be held so the label faces sky or ground when it strikes the ball during a horizontal swing. In this orientation, the bat is considered stiffer and less likely to break.
There are limitations to how much and where a baseball player may apply pine tar to a baseball bat. According to Rule 1.10(c) of the Major League Baseball Rulebook, it is not allowed more than 18 inches up from the bottom handle. An infamous example of the rule in execution is the Pine Tar Incident on July 24, 1983. Rules 1.10 and 6.06 were later changed to reflect the intent of Major League Baseball, as exemplified by the league president's ruling. Rule 1.10 now only requires that the bat be removed from the game if discovered after being used in a game; it no longer necessitates any change to the results of any play which may have taken place. Rule 6.06 refers only to bats that are "altered or tampered with in such a way to improve the distance factor or cause an unusual reaction on the baseball. This includes, bats that are filled, flat-surfaced, nailed, hollowed, grooved or covered with a substance such as paraffin, wax, etc." It no longer makes any mention of an "illegally batted ball". In 2001, MLB approved the use of Gorilla Gold Grip Enhancer in major and minor league games as an alternative to pine tar.
Do this for about three minutes, then collect the balls and work on 5-3, 6-4, and 4-6 plays for another three minutes. This is followed by hitting balls to the 5-6 hole. If the third baseman doesn’t get it, he retreats back to third, and the shortstop flips to third for a force-out, rather than throwing across or turn a long double play. The other fungo batter hits balls to the second baseman, who works on throwing to first.